Specs: 5 3/4" W X 2 4/8" H X 2" D
Instructions:1. Unscrew screw A from the back of the mirror.
2. Take out the glass mirror from it's housing.
3. Slide the Auxiliary Mirror on to the conventional mirror's inside housing using the bracket.
4. Using the wrench provided, tighten screws B & C until bracket tightly clamps to existing mirror's housing.
5. Place Auxiliary Mirror's glass back in it's housing and tighten screw A in the back.
6. Adjust Auxiliary Mirror to desired angle using thumbs.
Instructions:1. Unscrew screw A from the back of the mirror.
2. Take out the glass mirror from it's housing.
3. Slide the Auxiliary Mirror on to the conventional mirror's inside housing using the bracket.
4. Using the wrench provided, tighten screws B & C until bracket tightly clamps to existing mirror's housing.
5. Place Auxiliary Mirror's glass back in it's housing and tighten screw A in the back.
6. Adjust Auxiliary Mirror to desired angle using thumbs.
Instructions:
1. Pop off plastic Panel on the back of the auxiliary mirror using a regular flat screw driver.
2. Loosen screws A & B inside the Auxiliary Mirror unit from the top angle of the mirror - about 1/2 Inch using either a 1/4" socket or phillips head screw driver. NOTE: If you loosen screws A & or B too much, you could lose the bracket inside the mirror housing. If this happens, follow instructions A-D on instruction set B.
3. Slide the new mirror over the existing side view mirror allowing the bracket to slide between the mirror and the mirror's housing.
4. Tighten screws A & B until the mirror is securely connected.
5. Snap plastic panel back on the mirror (note: this panel or the whole mirror can be painted to match your vehicle).
6. Adjust the new mirror to desired angle using thumbs.
Instructions B:
A. Unscrew the C screw from the back middle of the mirror.
B. Take out the mirror from the front. This will give you access to the inside components.
C. Re align screws A & B with the bracket and tighten until attached.
D. Put mirror back in place and tighten screw C.
1. Pop off plastic Panel on the back of the auxiliary mirror using a regular flat screw driver.
2. Loosen screws A & B inside the Auxiliary Mirror unit from the top angle of the mirror - about 1/2 Inch using either a 1/4" socket or phillips head screw driver. NOTE: If you loosen screws A & or B too much, you could lose the bracket inside the mirror housing. If this happens, follow instructions A-D on instruction set B.
3. Slide the new mirror over the existing side view mirror allowing the bracket to slide between the mirror and the mirror's housing.
4. Tighten screws A & B until the mirror is securely connected.
5. Snap plastic panel back on the mirror (note: this panel or the whole mirror can be painted to match your vehicle).
6. Adjust the new mirror to desired angle using thumbs.
Instructions B:
A. Unscrew the C screw from the back middle of the mirror.
B. Take out the mirror from the front. This will give you access to the inside components.
C. Re align screws A & B with the bracket and tighten until attached.
D. Put mirror back in place and tighten screw C.
Instructions:
1. Unscrew screw A from the back of the mirror.
2. Take out the glass mirror from it's housing.
3. Slide the Auxiliary Mirror on to the conventional mirror's inside housing using the bracket.
4. Using the wrench provided, tighten screws B & C until bracket tightly clamps to existing mirror's housing.
5. Place Auxiliary Mirror's glass back in it's housing and tighten screw A in the back.
6. Adjust Auxiliary Mirror to desired angle using thumbs.
1. Unscrew screw A from the back of the mirror.
2. Take out the glass mirror from it's housing.
3. Slide the Auxiliary Mirror on to the conventional mirror's inside housing using the bracket.
4. Using the wrench provided, tighten screws B & C until bracket tightly clamps to existing mirror's housing.
5. Place Auxiliary Mirror's glass back in it's housing and tighten screw A in the back.
6. Adjust Auxiliary Mirror to desired angle using thumbs.